HT-14系列双余度线性可变差动变压器式LVDT线位移传感器
HT-14系列LVDT线位移传感器采用双余度冗余设计,热备份工作,是专为航空航天应用开发的高可靠性LVDT位移传感器。HT-14系列双余度LVDT外壳采用高强度航空不锈钢制造,产品性能优异。
产品特性:
  • 双余度设计,热备份工作

  • 精度高、重复性高、可靠性高、环境适应性强

  • 通道一致性高、通道交叉干扰低

  • 工作温区大

  • 动子组件可旋转,安装便捷

应用领域:
  • 航空航天

  • 高可靠性需求环境

  • 活塞位置反馈

  • 航空发动机

  • 燃气轮机

  • 电磁阀

  • 无人机

  • 飞行控制系统

产品规格:
  • 激励电压:6V 激励频率:3000HZ

  • 工作压力:4.5Mpa

  • 工作温度-55~+165

  • 使用高度:不低于11000

  • 灵敏度:0.0527V/V/MM

  • 灵敏度误差:<±0.5%FS

  • 重复性误差:<0.15%FS

  • 通道一致性误差:<0.5%FS

  • 温漂系数:<±0.015%FS

  • 产品介绍
  • 文件下载

  •   HT-14系列LVDT线位移传感器采用双余度冗余设计、热备份工作、差比和输出。是专为航空航天应用开发的高可靠性LVDT位移传感器。

      HT-14系列双余度LVDT外壳采用高强度航空不锈钢制造,产品性能优异。使用寿命高于30年,可在海拔10000米以上高空持续稳定工作。

      HT-14系列双余度LVDT位移传感器通过的试验项目:高温、低温、温度冲击、高低温循环试验、绝缘介电强度、淋雨试验、湿热试验、霉菌试验、盐雾试验、振动试验、加速度试验、酸性大气试验、电磁兼容试验、雷电感应敏感性试验、高强度辐射场、着火试验、静电防护试验、功能可靠性分析及故障模拟试验。


    Abek sensors has been a leading supplier of LVDT (Linear Variable Differential Transformer) and RVDT (Rotary Variable Differential Transformer) position sensors to the aerospace and power generation industry sectors for over 20 years.
    LVDT

    Abek sensors LVDT's operate using a non-contacting transduction principle, providing friction free motion and infinite resolution. Kavlico has refined this principle through manufacturing and test technology to make our LVDT's the standard for flight and fuel control position measurements. Our success stems from the ability to manufacture matched multiple sensors (channels) for redundancy.

    Multiple channels are provided in a variety of housing designs which may be mounted directly on airframe control and cockpit control surfaces or provided as an integral part of a servo valve or main ram actuator.


    LEADING THE MARKET IN POSITION SENSOR INNOVATION

    For over 20 years, abek sensors has led position sensor development in the aerospace industry. From researching the most advanced materials available, employing no-contact designs and highly skilled manufacturing practices, our products meet the most stringent demands of performance, size and quality.




    Common applications include fly-by-wire flight control systems, engine control systems and vehicle health management. Our products are typically developed from a custom set of requirements, however some key features include:

    • Qualification to RTCA D0-160
    • Up to four redundant channels
    • Hermetically sealed design
    • Measurement range from 0.2” (5mm) to 20” (500mm)
    • Accuracy better than 0.25% full scale deflection
    • Lane to lane tracking better than 0.5% full scale deflection
    • Able to withstand 5000psi pressure for actuator applications

    APPLICATIONS:

    • Flight control actuators for fixed and rotary wing aircraft
    • Engine fuel metering valve position
    • Engine variable geometry actuators